Whitestone Dome Glass Samsung Galaxy A50 Full Cover Screen Protector Reviews
- All languages ( 114)
- German ( 5)
- French ( 8)
- Spanish ( 1)
- Dutch ( 3)
- English ( 84)
- Danish ( 2)
- Finnish ( 5)
- Norwegian ( 3)
- Portuguese ( 1)
- Russian ( 1)
- Swedish ( 1)
Showing 1- 10 of 114reviews ( )
There are more reviews in other languages. Show all languages to see more reviews and we can translate them for you.
Make sure you take your time and have a couple of views of some YT tutorials to familiarise yourself on the process.
I didn't use the instructions and just went straight onto it after watching this a couple of times: https://youtu.be/0exoM82x6fc
Expensive but it's a quality above the rest ????
One it arrived - the install process is a bit complex but do-able. I would suggest doing it on a COMPLETELY flat surface. I thought my desk was flat but it's got a slight angle, which made pouring the liquid and putting the screen on a bit tough and had to start over with the second bottle of adhesive.
After two weeks of having this on, I dropped my phone face down on concrete. The screen protector was completely broken, and I really thought my screen was as well, but peeled off the protector and the screen was untouched!
I'm going to buy another it's this good.
I installed this for my father and he is very impressed. I am also
Packing: 5 Star
Product Quality: 5 Star
Installation: 4 Star (its a but tricky to get it write in first time, I had to do it twice)
Fingerprint sensor works fine after installation with few hiccups occasionally
I thought it looked over complicated but its not, follow the video and your done in under 3 minutes.
And best of all the ultrasonic fingerprint reader works perfectly!
Installation was very difficult, followed all steps correctly and still went wrong. Funnkly enough in the install video it goes wrong in the same way and then cut jumps to a fixed one! I had to use the backup UV resin tube and got a hair stuck below it with all the messing about.
Be sure to follow the instructions exactly.
I was a little dubious about putting glue on my screen.
Following the instructions exactly, it went on flawlessly first time.
After having a screen protector that was only glued around the edges, I am very impressed with the results.
You can hardly tell it's there and it looks like the original screen, due to no air gap.
Dropped my phone and although it cracked it saved my phone screen.
Feels and looks like there is no screen protector on, fingerprint works fine.
However, like a lot of people have mentioned, the fingerprint sensor - it only works 50% of the time, even after following the newest application guide which asks you to press hard on the sensor after an initial curing, as well as checking countless youtube videos. Lucky for me, I don't use it often - but it is a bit frustrating for some apps e.g. banking authentication.
The other thing was the application... Really, I'm pretty good at this sort of thing, so I followed the instructions to the letter but after removing the catch to release the screen protector onto the screen, on one long side of the phone the adhesive moved like a pincer so that it met that particular edge of the phone in two places. Then from those two points the adhesive moved along the edges and joined together, basically wrapping around and leaving an air pocket between the middle and edge of the phone. I left it for about an hour, but the air pocket hadn't changed one bit. I hope I've described that well enough. It could have been debris but I religiously wiped the screen clean first using alcohol pads and what they provided/instructed. I also even boiled a pot of water in the room for 20 minutes or so to reduce the amount of dust in the air.
Luckily they provide a second vial of adhesive, otherwise that would have been $$$ down the drain. Still, the cleanup job after the botched attempt was messy, making it harder to ensure the inside of the CURVED screen protector was completely clean and dust free.
This all being said I'm giving 4 stars because I do think the finish is top quality and my phone screen feels protected.
By the way, this Galaxy S10 screen protector is compatible with the UAG Pathfinder series (I have the camo version). Just wanted to mention this because no one else has (I checked for days)!
Upgraded- first thing I did was order another one of these before I even turned the phone on.
Best screen protection I've ever had and worth every penny!
I am a techie by trade, but even I was a little intimidated by the proposed installation process. I read the instructions.... something I don't normally do..... and watched the videos etc. During the installation, as the fluid was dispersing across the screen, I noticed that a very small air pocket had been trapped near the ear piece. The instruction said not to touch the protector and if there were air pockets, then the screen could be removed, cleaned and the kit included a 2nd vile of fluid to use for a 2nd attempt if needed. I also noticed that the hole for the camera was not exactly lined up correctly. Since I had nothing to lose, rather than going straight to taking the screen off, I just tried to gently squiggy the bubble to the edge with my fingernail while also moving the protector the 1mm or so to correctly line up the camera hole. The protector was very easy to move as it was essentially floating on liquid, and so I was very easily able to align the camera hole correctly. The air bubble got smaller, but I couldn't get it right to the edge without perhaps more pressure than I was willing to apply....however, it was very small now, so far to the top of the screen as to be higher than the camera and not at all in the normal field of view, that I decided it was acceptable and not worth the risk of removing, re-cleaning perfectly and retrying for the sake of it.... so I proceeded to the curing process.
After full curing and on closer inspection, I do see what I could only describe as 'stress lines' in the adhesive at the very top of protector, obviously due to my squigging attempts earlier, but again barely noticeable and then only if you were looking for issues.
All in all, the protector was flawless and the final picture and feel are near perfect. If I was doing it again, the only thing I would say to look out for, is the camera alignment... perhaps the fixture could be tilted or something to align correctly, rather than touching the screen as I did. I think the air bubble was just unfortunate in my case and I wouldn't expect a repeat if I was to try again.... but as I said, the bubble was so small and out of the way that I was perfectly fine with it.
I mentioned at the beginning, that the Finger Print Scanner worked about 75%.... and this was after I increased the sensitivity and retrained my finger prints. The FPS does work 100% better than it did with pretty much any other (cheaper) protector I've tried, but I do find that I sometimes need to be a little patient with it and have to try 4, 5 or maybe 8 times for it to work (sometimes it'll work first time!).... maybe it's my finger prints?? :)
Anyway, generally very happy. Very happy to recommend and I would happily use again for my current or next phone.... 4.5/5, losing 0.5 for price and non-perfect fit requiring manual adjustment for camera alignment.
Sadly, with the sonic fingerprint technology in the S10, it's just not got it. I've never had an issue with a fingerprint reader but the only way I can make the S10 work is with no protector. Since this sells itself as compatible and even approved by Samsung for it, it's disappointing to say the least.
It's a great product, but not so great for the S10.
One possible downside is that it definitely compromises the fingerprint scanner. Mine still works but not as well as without the glass. Not a problem though as the face recognition on my Samsung S10 also kicks in when necessary.
MobileFun is an excellent vendor. They ship right away and even refunded my purchase of a protector I ordered by mistake.
Would definitely recommend!
Only negative I encountered was after pulling the clip out and the screen falling into the glue, multiple bubbles immediately appeared and I had to spend a good few minute trying to get them out. I followed all the previous instructions and there was no specks on the screen so I'm not sure what exactly caused the bubbles.The ones I couldn't get are right where the glass begins to curve, so I guess it's not that big of a deal.
Next time I'll go to a store to have it installed, simply to avoid any bubbles.
All instalation instructions were followed and phone received no knocks.
Very nice feel and the installation was easy but you'd have to watch the tutorial multiple times before installing.
The only issue I have is that my fingerprint only works 50% of the time even after redoing the fjngee print as instructed to do so. Really disappointed with this part of the cover especially as I paid for a premium cover
As far as the product goes it was easy to apply but make sure you pay attention to the instructions AND the video. In the video it tells you to hold your thumb down on the bottom of your screen for a minute before curing the product for the last time for a minute on top and bottom. I did not do this and half the time the Fingerprint scanner won't register like there is a small gap inbetween the screen protector and my phone. Other than that it works flawlessly.
Protects the screen
Air under display near top
Finger print scanner requires more tries
Protector scratches alot easier than the phones actual glass
Mobile fun where very professional in resolving my situation with a replacement kit and updating the installation video
Even the new ultra sonic fingerprint scanner is working fine.
PS.: Watch the video few times before install and take your time.
Sorry, no matching reviews have been found. Please check the filters you have applied.
Please check the filters you have applied or you can Show all languages to see reviews and we can translate them for you.